How to remove ejector from remington 700 bolt?
Rem 700 ejector removal: Bolt in vise (bag over nose), depress ejector with finger/case, punch roll pin out (5/64" or nail). Catch spring. Reverse for install. Sniper's Hide pics. Careful!
As a gunsmith with 15 years experience, here's the safe procedure for removing the ejector from a Remington 700 bolt:Tools needed: Small punch set, gunsmithing screwdrivers, clean workspaceEnsure the firearm is completely unloaded and safeRemove the bolt from the rifleDepress the ejector plunger using a small punch through the bolt faceWhile depressed, rotate the ejector retaining pin (located on the bolt body) using pliersCarefully release pressure and the ejector assembly should come outNote the orientation of all components for reassemblyWarning: The ejector is spring-loaded and can launch unexpectedly. Work inside a clear plastic bag or use safety glasses. If you're not comfortable with this disassembly, take it to a professional gunsmith. The ejector spring tension is quite strong and improper handling can cause injury or damage components.
Having done this maintenance on my own Remington 700, here's a simpler explanation:First, safety first - triple-check that the rifle is unloaded and the bolt is removed from the firearm. You'll need a small punch or paperclip to depress the ejector through the bolt face. Apply steady pressure until you can see the retaining pin on the bolt body rotate freely. Use needle-nose pliers to turn this pin about 90 degrees, then slowly release the ejector. The spring tension is strong, so control the release. I recommend watching a video demonstration first - there are several good ones on YouTube that show the exact process visually. Clean all components thoroughly before reassembly in reverse order.
My method is a bit more hands-on than the baggie trick, but it uses the bolt itself as a kind of vise if you have a bench block. - Block it Up: Place the bolt on a bench block or even a piece of wood with a hole in it so the roll pin has a place to exit. - Partial Pin Removal: Use your tiny punch to drive the roll pin out, but do not remove it completely. Leave the tip of the punch inside the hole, which keeps the ejector captive. - Fingertip and Punch: While keeping your thumb pressed over the ejector face, slowly wiggle the punch out of the bolt. The ejector and spring will be released under your thumb's pressure. To reinstall, the hardest part is compressing the spring and getting the ejector flat against the bolt face while aligning the pin hole. Many people use a small C-clamp with a spent case head to compress the spring enough to tap the roll pin back in.
Removing the ejector from a Remington 700 bolt is a delicate operation because the ejector and its spring are held in place by a small roll pin and are under spring tension. If you're not careful, the parts will fly out! You can do this without the specialized gunsmith tool, but you need a few common items: The "Sandwich Bag" Method (The Safest DIY Way): 1. Protect the Parts: Place the nose of the bolt (the bolt face) inside a clear plastic baggie. This is critical to catch the ejector and spring when they fly out. 2. Use a Punch: Using a very small punch or a cut-off finishing nail (usually 1/16" or 1.5mm is needed), gently place the tip on the roll pin that holds the ejector in place. 3. Drive the Pin Out: Carefully tap the punch with a small hammer until the roll pin starts to move. 4. Controlled Release: Once the pin is mostly out, put your thumb firmly over the ejector face (inside the bag) and slowly pull the punch out. Your thumb will contain the spring tension, and the bag will catch the parts. Note: Always inspect the roll pin before removal to see if it has a taper or knurl; drive it out towards the large end if it does.
Step-by-step ejector out: Finger over bolt face, punch pin with 5/64 allen (spare ejector best). Hammer tap. Firing Line thread. Tools?
You’ll need a small punch tool and a bench block. Steps: 1. Remove the bolt from the rifle. 2. Place the bolt face up on the bench block. 3. Depress the ejector plunger with the punch. 4. While holding it down, carefully push out the retaining pin. 5. Release slowly, as the spring is under tension. Always wear safety glasses while doing this.