Katharine Colleran

Launch an EC2 instance · Sign in to the AWS Management Console and open the Amazon EC2 console at https://console.aws.amazon.com/ec2/. · Make sure you have not.

St Joseph's College Hunters Hill

Address: Mark Street, Hunters Hill NSW 2110, Australia

Lido is intended to remove the adversarial incentives of ETH 20 by allowing users to stake their ETH while simultaneously participating in on-

We have everything you need under one roof to finish your space including the expert design help to guide you all the way We would ❤️ to help

To unlock hero Apex Legends you have to collect 12000 tokens Each Apex Legends level up you'll get 600 Legend Tokens After you unlock Apex Legends hero you can play it and change hero skins

Antonov An-225 Mriya -- the largest aircraft by weight, length and wingspan The six-engined Antonov An-225 is literally in a category of its own, holding the titles of both the heaviest aircraft ever built and the largest wingspan of an aircraft currently in service

SUMI NAILS

Address: Shop15, Lower Ground, 227 Elizabeth St, Sydney NSW 2000, Australia

An alternative template engine can be used with embedded Javascript templates.

In this article, you will learn how to apply EJS to an Express application, include repeatable parts of your site, and pass data to the views.

If you would like to follow along with this article, you'll need these.

The original instructions were written for express v4.17.1 and ejs v3.1.5. It has been verified with a number of different things.

First, open your terminal window and create a new directory.

Go to the directory that was created.

You can start a new project at this point.

You will need to install the express package.

The ejs package needs to be installed.

At this point, you have a new project ready to use.

Let's set up the routes for the index page and the about page with all of the dependencies installed.

Add the following lines of code when you open a new server.js file.

The code defines the application.

This code sets the view engine for the Express application.

The code sends a view to the user.

It is important to note that the views folder will be looked in by the rendering function. Since the full path is views/pages/index, you only have to define pages.

Next, you will create views using EJS.

A lot of the code that you build will be used again. These are considered partials.

There are three partials that will be used on the index page and about page. Let's make those files now.

A new views directory can be created.

Then, create a new subdirectory.

If you want to open the new head.ejs file with your code editor, you have to create a new directory in this one. The following lines of code are needed.

The head is contained in this code. It also has other styles.

Next, open the new file with your code editor.

The following lines of code are needed.

This code uses several classes from the bootstraps for styling and has a navigation for anhtml document.

Next, open the new footer.ejs file with your code editor.

The following lines of code are needed.

The code uses several classes from bootstrap for styling.

You will use the partials in index..ejs and about..

There are three partials defined for you. You can now include them in your views.

Use %- include('RELATIVE/PATH/TO/FILE') %> to add an EJS partial in another file.

Next, create a new page.

You can open the index.ejs file with your code editor.

The following lines of code are needed.

Save the changes to this file and then run the application.

You can see the index page if you visit http://localhost:8080/ in a web browser.

Next, open the about.ejs file with your code editor. The following lines of code should be added.

This code shows how partials can be structured to reuse across different pages.

Save the changes to this file and then run it.

You can see the About page in a sidebar if you visit it in a web browser.

Now you can use the EJS to pass data from the application to the views.

Let's define some variables and a list to send to the index page.

Add the following lines of code to the app.get('/') route by re-reading server.js in your code editor.

The code defines an array of mascots and a string. Let's use them in index.ejs.

You can use %> to echo a single variable.