which doughboy pools can be buried?

A swimming pool is not usually considered a building since it doesn't protrude from the ground and it is almost always at a height of less than 1.50 meters. They don't compute buildability orOccupancy on the plot. It is important to know that any intervention or work on a plot is required for a license or communication in the town hall.

Any earth moving work within a plot requires a technical project. Someone has to supervise the regulations before placing a pool.

Some people argue that a license is not necessary for a pool that is pre-made. If we place an inflatable pool on the ground, there will be no legal problems. If we want to bury it, it will be necessary to notify the town hall through the prior notification procedure, accompanied by a small project or report.

It is the same if we bury it completely or if we partially bury it, since this implies a movement of earth, even if it is small, and that it will not be dismounting.

The type of soil on which the plot is located must be checked by the designer before a pool is placed. If the land is urban, the only condition is that setbacks to boundaries and alignments are respected, which is usually 3 meters. We can't glue our pool to the edge of the plot.

We will have more conditions if the land is rustic.

The setbacks to the boundaries usually increase to 5 meters. We must justify the use and location of the rustic land since it is intended for agricultural, forestry, etc. Sometimes a pool can report illegal housing.

Technical issues must be solved once the urban conditions have been overcome. The procedure is the same for burying a plastic pool and a steel pool.

canvas pools can be dangerous because they are not usually prepared for burying. If you're thinking of installing a pool in your home, you can visit our post on the types.

It will be necessary to dig to the right depth and place a concrete slab that will serve as the base for the pool. The depth of the excavation will be the height of the pool and the thickness of the screed.

The resistance of the soil, its consistency and the angle formed by its slope are all assessed. We need to make small retaining walls to support the ground and not exert pressure on the pool.

If the ground is good and the pool glass is good, you can fill the gap between the two with gravel. It would be interesting to put some type of insulation between the wall and the pool.

You have to reserve a space for the facilities that come in the kit.

The location is located

The ground where the pool is to be installed must be undisturbed and sturdy, with no grass, roots or stones that could pierce the bag. Choose a sunny area close to a drain, water supply and electrical outlet, where there are no underground connections, and protected from the wind, and without trees. Don't install under power lines. The treatment plant must be at the same level as the pool.

Remember, 1,000 LITERS is 1 M3 is 1000KGS.

The ground preparation is done.

We will install the pool in the space that is marked.

The diameter of the hole in your pool should be 1 meter larger than the diameter of your pool. The pool will be 1 meter longer and 2 meters wider if it's an oval pool.

The location of the skimmer-return and the ladder is what you must consider.

The depth will be 15 cm higher than the pool's height. The depth should be 1.35m if your pool is 1.20m high.

The concrete must be smooth and level. If you want to avoid damaging the liner, place a protective blanket or expanded polystyrene sheets with a maximum thickness of 10mm on top of the screed.

Final installation.

Proceed to assemble the pool and join the treatment plant accessories with rigid or semi-rigid PVC pipe. The pool should be filled with water.

Adhere the expanded polystyrene sheets to the outside of the pool sheet with the help of the tape.

The free space between the pool sheet and the earth slope should be filled with poor concrete.

The poor concrete should be distributed around the entire perimeter. Proceed in stages, 30 cm by 30 cm, in order for the concrete to settle properly.

The future of the pool depends on this operation, since the poor concrete will be in charge of avoiding any possible accidents.

NEVER leave the pool without water.

Tools needed.

You will need Gloves, star screwdriver, tape measure, cutter, set of open-end wrenches and clothespins to assemble your pool.

It will be necessary to build a concrete floor with mesh and 15 cm thick once the place has been defined. It is important that this platform is level.

The excavation must be at least 15 cm taller than the pool.

The instructions for assembling the pool are included with the pool.

When the pool is fully assembled, it is necessary to attach 2 cm thick polystyrene sheets to the outside of the steel sheet.

The plates prevent direct contact between the structure and the wall.

The wall can be built around the entire perimeter of the pool.

The pool supports the pressure and weight of the water. The metal structure is reinforced by the supports of some oval pools. The function of the wall is not to make the pool more resistant (it is not a retaining wall as it would be in a built-in pool) nor is it a substitute for the lateral supports, but it is only to contain the earth on which it is buried. the pool, without it putting pressure on the pool walls.

The location of the skimmer, the return valve and the ladder are important. The treatment plant must be at the same level as the bottom of the pool.

There is a drain, a water outlet and an electrical outlet in the sunny area.

It should not be placed under power lines or underground connections because they can cause problems with the water and nearby trees.

Don't leave the pool without water. The weight of water makes the structure stable. The walls could lose their tension and lean when emptied.

The instructions in the instruction manual do not correspond to the steps that can be taken to repair the assembly.

The process of Piscinas Gre is described in the video.